История
22 апреля 2021
Часть переводимой страницы WBIO-AI-DV-12 I/O Module.
+22
FuzzyBot переименовал страницу WBIO-AI-DV-12 I/O Module/en в WBIO-AI-DV-12 Analog Inputs/en без оставления перенаправления: Часть переводимой страницы WBIO-AI-DV-12 I/O Module.
м
27 ноября 2019
26 ноября 2019
Нет описания правки
Нет описания правки
+1
Нет описания правки
+68
Нет описания правки
−109
Нет описания правки
+4
Нет описания правки
+16
15 июля 2019
Новая страница: «== Images and drawings of the device == {{WBPicturesNoDrawing|1}} <!--{{WBPicturesNoDrawing|2}}-->»
−28
Новая страница: «<!-- For models designed to measure current, the'scale' factor must be set to 0.1 -->»
−115
Нет описания правки
+14
Новая страница: «{| class="wikitable" style="text-align:center" |+ Dependence of the input operation mode on the installed jumper and scaling factor !"'The presence of the jumper"…»
−255
Новая страница: «{| class="wikitable" style="text-align:center" |400px|thumb|right|Add channel list |File:Ai-dv-12-only-scale.png|400p…»
−103
Новая страница: «For each channel, you can specify a conversion factor (scale) corresponding to the measurement mode. Restartujte service wb-mqtt-serial after changes: <code>> ser…»
−609
Новая страница: «Previously, when connecting the module via WB-MIO or WB-MIO-E, there was no possibility to select the input mode from the web interface. We recommended creating c…»
−338
Новая страница: «'''Warning, the information below is outdated and will be deleted!'''»
−31
Новая страница: «The WBIO-AI-DV-12 module can also be connected via the interface Converter WB-MIO. Two device templates can be used: WBIO-AI-DV-12-50V and WBIO-AI-DV-1…»
−404
Новая страница: «File:Scale_WBIO_AI_DV_12.png|500px|thumb|right|the value of the scale factor of the dimensions '''scale''' is chosen equal to 0.2126 for measuring voltage of ±…»
−175
Новая страница: «'''Unlike other WBIO modules, only one instance can be connected to a single controller or interface module.'''»
−112
Новая страница: «== Connection via WB-MIO interface converter ==»
−53
Новая страница: «{| class="wikitable" | 500px|thumb|center|login mode Settings | File:Dv12web3.png|500px|thumb|center|Display inputs with different operati…»
−410
Новая страница: «After the necessary settings and saving changes, the device will be displayed in the '''''Devices'''''tab.»
−71
Новая страница: «Now you can activate the desired mode in the ''Channels'' tab. Channels are denoted as '''''Channel Ax''''', where 'x' corresponds to the entry number. To activat…»
−423
Новая страница: «{| class="wikitable" | 500px|thumb|center|Desired configuration file | File:DV12WebInterface2.jpg|500px|thumb|center|Module select…»
−43
Новая страница: «To connect, you need to dock the WBIO-AI-DV-12 module to the right of the WIren Board controller, making sure that all the connector pins on the module get into t…»
−328
Новая страница: «'''Unlike other WBIO modules, only one instance can be connected to a single controller or interface module.'''»
−112
Новая страница: «== Connection to the controller ==»
−20
Новая страница: «Each input has its own contact group (pin connectors on the board). Contact groups are located opposite the terminal block of the corresponding input and are mark…»
−277
Новая страница: «{| class="wikitable" | 200px|thumb|center|jumper | rowspan="2" | 300px|thumb|right|Module with removed cover | rowsp…»
−110
Новая страница: «Installation of jumpers is carried out on the contact groups related to the corresponding inputs. To do this, remove the top cover of the device by pulling it thr…»
−856
Новая страница: «== Installing jumpers ==»
−19
Новая страница: «Under the order is available hardware modification of the module WBIO-AI-DV-12 with the ability to measure the current 0 — 20mA. The module in this modification…»
−161
Новая страница: «In this mode, the voltage difference applied to the corresponding analog inputs will be measured. <!-- '''''Current measurement''''' File:Current_Sensor.png|500…»
−245
Новая страница: «This mode also uses two adjacent analog inputs. You should <u>to install jumpers</u> to the contacts pertaining to both inputs. In the web interface of the contro…»
−239
Новая страница: «'''''Differential voltage input is ±50 V'''''»
−33
Новая страница: «The principle of operation of the differential input is to compare the two values and output the difference between them as readings. Accordingly, to activate thi…»
−375
Новая страница: «This mode requires external calculations and the allocation of one of the 12 channels as a reference. Not supported in standard SOFTWARE. --> '''''Differential vo…»
−130
Новая страница: «<!-- ""'±50 V single-pole voltage input'""»
−33
Новая страница: «To set the input to this mode, you must set the appropriate setting in the web interface of the controller (for details, see WBIO-AI-DV-12_I/O_Module/en#Connect…»
−237
Новая страница: «{| class="wikitable" style="text-align:center" |+ Dependence of the input operation mode on the installed jumper !'''The presence of the jumper''' !! '''Operating…»
−215
Нет описания правки
−15
Новая страница: «This module has several modes of operation (they are described in more detail in the table below). Changing the operating mode is carried out by installing jumper…»
−166
Новая страница: «== The setting of the operation modes ==»
−12
Новая страница: «{| class="wikitable" !colspan="2" | '''Terminals and wire section''' |- || The recommended wire cross section with pin bushing insulated tip, mm<sup>2</sup> ||…»
−51
Новая страница: «mini|420x600px|overall dimensions {| class="wikitable" !Parameter !Value |- ! colspan="2" |General |- | rowspan="2" |Number of inputs |12 (uni…»
−565
Новая страница: «==Technical specifications==»
−30
Новая страница: «The measurement modes are set by means of jumpers inside the module body. The module is galvanically isolated from the controller circuits, including iGND line. <…»
−192
Новая страница: «For easy connection, each pair of inputs is output to one of 6 terminals. In addition to the inputs, each terminal block has +5 V and iGND lines, but the maximum…»
−226