WB SH 3.5: Errata
0350001: Insufficient peak current
Revision:
3.5
Description
In a small part of devices shipped before 10.06.2014, the power supply circuit incorrectly limits the output current.
Symptoms
- The Board sometimes reboots when you boot right after initializing the USB hub
- The Board reboots when GSM is running at a poor signal level.
How to fix
The current-setting resistor needs to be replaced. Contact technical support. See also 0350004
0350002: Intermittent shutdown leads to the impossibility of download
Revision:
3.5
Description
After a short (<1s) shutdown of the WB SH using the switch on the case, the device does not boot.
How to fix
-
Workarounds
Turn off the board for a few seconds, then turn back on.
Reason
Undocumented processor behavior.
0350003: Work with DMX512 is not supported
Revision:
3.5
Description
The built-in RS-485 ports cannot be set to 250 kBaud. This makes it impossible to work with DMX-512.
How to fix
Need to replace the crystal oscillator, and recompile Device Tree/en. Recommended value: 24MHz.
Workarounds
Use a USB-RS485 adapter.
For example: (http://ru.aliexpress.com/item/Free-Shipping-USB-to-RS485-485-Converter-Adapter-Support-Win7-XP-Vista-Linux-Mac-OS-WinCE5/1896086704.html , http://www.dx.com/ru/p/usb-to-rs485-module-black-221402?tc=RUB&gclid=COavlbDOgb8CFeHbcgodIjUAOg#.U6CSrv53TFU )
It is recommended to use adapters on the FT232RL chip and the like.
Delivery of fixed Wiren Board Smart Home is possible.
Reason
The wrong value of the crystal oscillator.
0350004: Insufficient peak current (2)
Revision:
3.5, S/N before 230
Description
In devices shipped before 20.06.2014 (serial numbers less than 230), the power supply circuit incorrectly limits the output current.
Symptoms
If GSM is active and the signal level is poor, it can be observed under certain conditions:
- reboot the Board
- disable and reconnect the Wi-Fi module
- Ethernet shutdown
How to fix
Unsoldering capacitor C11 fixes the problem. See diagram.
0350005: Leads from GSM on prtctrl line
Revision:
3.5
Описание
Линии PRTCTRL (управление питанием USB-устройств) подвержены влиянию наводок от излучения GSM-антенны. При высокой выходной мощности GSM и близком расположении антенны, наводки приводят к кратковременному снятию питания с USB-устройств.
Симптомы:
При активной работе GSM при плохом уровне сигнала при определённых условиях могут наблюдаться:
- отключение и переподключение модуля Wi-Fi
- отключение и переподключение внешних USB-устройств
Как исправить
- Поменять расположение встроенной GSM-антенны в корпусе
- Вынести встроенную GSM-антенну за пределы корпуса
- Использовать внешнюю антенну GSM
0350006: Проблемы с включением платы
Ревизия:
3.5
Описание
Неправильное значение конденсатора C5 в очень малом количестве плат, отгруженных до 10 июня 2014.
Симптомы:
Наблюдаются проблемы с включением платы: устройство включается только после нескольких переключений кнопки on/off.
Как исправить
- Поменять конденсатор C5 на конденсатор ёмкостью 1 мкФ (см. рисунок)