WB-MGE Modbus-Ethernet Interface Converter/en: различия между версиями
(Новая страница: «300px|thumb|right|overall dimensions {| class="wikitable" ! style="text-align: center;" | Option ! style="text-align: center;" | Value |- ! c…») |
(Новая страница: «==The Ethernet connection and the unit's network settings==») |
||
Строка 111: | Строка 111: | ||
|} | |} | ||
== | ==The Ethernet connection and the unit's network settings== | ||
Модуль WB-MGE подключается к локальной сети Ethernet к порту маршрутизатора либо напрямую к одному из портов Ethernet программируемого контроллера Wiren Board. | Модуль WB-MGE подключается к локальной сети Ethernet к порту маршрутизатора либо напрямую к одному из портов Ethernet программируемого контроллера Wiren Board. |
Версия 16:12, 19 июля 2019
Purpose
WB-MGE interface converters are designed for remote connection of Modbus RTU devices with RS-485 interface via Ethernet (Modbus RTU over TCP Protocol). It is possible to connect the controller directly to the module, as well as through the local network or the Internet.
Interface conversion
There are three modifications of WB interface converters: WB-MIO, WB-MIO-E and WB-MGE. The table below shows which interface each module converts to.
Model | From | To | |||
---|---|---|---|---|---|
RS-485
(Modbus) |
Ethernet
(IP) |
WBIO | RS-485
(Modbus) |
Ethernet
(IP) | |
WB-MIO | + | + | |||
WB-MIO-E | + | + | + | ||
WB-MGE | + | + | + | + |
Technical specifications
Option | Value |
---|---|
Power | |
Supply voltage front-end | 9 V — 24 V DC |
Power consumption |
0.85 W |
Terminals and wire section | |
Recommended wire cross-section, mm2 | 0,75 — 1 |
Length of the standard sleeve , mm | 8 |
Torque of screws, N∙m | 0,2 |
Communication | |
Communication protocol | Modbus RTU |
Interfaces |
|
RS-485 interface parameters | set programmatically, by default:
speed 9600 bps; data bits 8; parity N; stop bits 2;
|
dimensions | |
Size | 2 DIN; 36,3x90,2x57,5 mm |
Operating conditions | |
Air temperature | -40°C to +80°C |
Relative humidity | up to 92%, no condensation |
The Ethernet connection and the unit's network settings
Модуль WB-MGE подключается к локальной сети Ethernet к порту маршрутизатора либо напрямую к одному из портов Ethernet программируемого контроллера Wiren Board. Питание подаётся на клеммы V+ и GND модуля WB-MGE. Модуль не поддерживает питание PoE.
В сети Ethernet по умолчанию WB-MGE имеет статический IP адрес 192.168.0.7. Внимание: если в локальной сети используется диапазон адресов, отличный от 192.168.0.0/24, то при подключении через маршрутизатор связи с устройством не будет и потребуется дополнительная настройка. Подробную инструкцию по настройке Ethernet-части WB-MGE можно найти на странице Настройка Ethenet-интерфейсов и подключение модулей WB-MIO-E и WB-MGE.
Modbus-регистры
Описание регистров можно найти на странице Преобразователи интерфейсов WB-MIO и WB-MIO-E в разделе "Управление по Modbus".
Изображения и чертежи устройства
По ссылкам ниже вы можете скачать изображения и чертежи устройства WB-MGE.
Corel Draw 2018: WB-MGE.cdr.zip
Corel Draw PDF: WB-MGE.cdr.pdf
Autocad 2013 DXF: WB-MGE.dxf.zip
Autocad PDF: WB-MGE.pdf