Первое включение Wiren Board Smart Home/en: различия между версиями
(Новая страница: «To connect an external antenna, use the adapter with u.fl to SMA. The location of u.fl GSM and Wi-Fi connectors is shown on the description page.») |
(Новая страница: «U.fl connector for external 433MHz antenna is located next to the base of the pin antenna, when connecting an external, unsolder/bite off the internal pin antenna.») |
||
Строка 28: | Строка 28: | ||
To connect an external antenna, use the adapter with u.fl to SMA. The location of u.fl GSM and Wi-Fi connectors is shown on the description page. | To connect an external antenna, use the adapter with u.fl to SMA. The location of u.fl GSM and Wi-Fi connectors is shown on the description page. | ||
U.fl connector for external 433MHz antenna is located next to the base of the pin antenna, when connecting an external, unsolder/bite off the internal pin antenna. | |||
'''При слабом сигнале сотовой сети возможна нестабильная работа контроллера с внутренней антенной GSM.''' Используйте внешнею и располагайте ее вдалеке от контроллера. | '''При слабом сигнале сотовой сети возможна нестабильная работа контроллера с внутренней антенной GSM.''' Используйте внешнею и располагайте ее вдалеке от контроллера. |
Версия 13:04, 19 июля 2019
"'This article is relevant for wiren Board 3.5"' [Problem with memory cards in the first batch of devices]
Preparing to power on
Before work
- Be sure to insert the software image microSD card (included) into the device.
- Install a micro SIM card (if you plan to use a GSM module).
- Check the switch position.
- Connect the power supply.
microSD card
Installed in the connector for memory card (top) contacts up.
Micro-SIM card
It is installed in the connector for Micro-SIM card ("lower") contacts down cut corner inside.
Switch position
The pressed side with a dot is 'off'.
Power supply
There are three types: standard, DIN-rail, PoE-injector. Do not connect two different power supplies at the same time, it will burn them and the controller. The standard power supply is connected to the appropriate connector. The power supply on a DIN rail connect the wires to the big terminals Vin and Gnd (next to the relays, see diagram http://contactless.ru/wiki/index.php/%D0%A4%D0%B0%D0%B9%D0%BB:WB3.5.png) The Passive PoE power supply is connected by an Ethernet cable.
Antenna connection
As standard, the controller comes with a connected internal Wi-Fi antenna, radio 433 and an external GSM antenna on the SMA connector (in the first batch were supplied with an internal GSM antenna).
To connect an external antenna, use the adapter with u.fl to SMA. The location of u.fl GSM and Wi-Fi connectors is shown on the description page.
U.fl connector for external 433MHz antenna is located next to the base of the pin antenna, when connecting an external, unsolder/bite off the internal pin antenna.
При слабом сигнале сотовой сети возможна нестабильная работа контроллера с внутренней антенной GSM. Используйте внешнею и располагайте ее вдалеке от контроллера.
Первое включение
Первое включение устройства может занять длительное время (3-4 минуты). При первом включении происходит создание секретных ключей для ssh и производится инициализация серийного номера устройства.
IP-адрес
При подключении по Ethernet Wiren Board Smart Home автоматически получает IP-адрес по DHCP. Узнать IP-адрес, который получило устройство можно в списке подключенных клиентов в административном интерфейсе вашего роутера.
Доступ по SSH и консоль
Стандартные имя пользователя и пароль: пользователь: root, пароль wirenboard
Обновление ПО
Рекомендуем выполнить обновление ПО. См. http://contactless.ru/forums/topic/%D0%BE%D0%B1%D0%BD%D0%BE%D0%B2%D0%BB%D0%B5%D0%BD%D0%B8%D1%8F-%D0%BF%D0%BE/