12 063
правки
(Новая страница: «In the current version there is no protection against charging at low temperatures. Be careful, the batteries deteriorate from this.») |
|||
(не показано 11 промежуточных версий этого же участника) | |||
Строка 6: | Строка 6: | ||
Here is a description of Wiren Board controller version 2.8. | Here is a description of Wiren Board controller version 2.8. | ||
Wiren Board consists of two printed circuit boards: | Wiren Board consists of two printed circuit boards: | ||
* modified [[iMX233-OLinuXino-MICRO/en]] | * modified [[iMX233-OLinuXino-MICRO/en]] | ||
Строка 16: | Строка 15: | ||
* NFC on NXP chip [[PN532/en]]. The antenna for NFC is drawn around the perimeter of the Board. See also [[NFC/en]] | * NFC on NXP chip [[PN532/en]]. The antenna for NFC is drawn around the perimeter of the Board. See also [[NFC/en]] | ||
* USB to Ethernet Converter and USB hub SMSC [[LAN9514/en]] | * USB to Ethernet Converter and USB hub SMSC [[LAN9514/en]] | ||
* [[RS-485/en] - [http://www.analog.com/en/interface-isolation/rs-485-rs-422/adm3483/products/product.html ADM3483]. | * [[RS-485/en]] - [http://www.analog.com/en/interface-isolation/rs-485-rs-422/adm3483/products/product.html ADM3483]. | ||
* 8-channel analog multiplexer for ADC (7 terminals and supply voltage). See also [[ADC/en]]. | * 8-channel analog multiplexer for ADC (7 terminals and supply voltage). See also [[ADC/en]]. | ||
* Open collector outputs for [[Hardware_Low_voltage_control/en|Hardware Low voltage control]] | * Open collector outputs for [[Hardware_Low_voltage_control/en|Hardware Low voltage control]] | ||
Строка 22: | Строка 21: | ||
* SPI-GPIO-expander - Microchip [[MCP23S08/en]] | * SPI-GPIO-expander - Microchip [[MCP23S08/en]] | ||
* The power supply circuit on the chip [http://www.linear.com/product/LTC4002 LTC4002] | * The power supply circuit on the chip [http://www.linear.com/product/LTC4002 LTC4002] | ||
Строка 64: | Строка 62: | ||
In the current version there is no protection against charging at low temperatures. Be careful, the batteries deteriorate from this. | In the current version there is no protection against charging at low temperatures. Be careful, the batteries deteriorate from this. | ||
''' | '''It is necessary to meet the battery polarity!''' | ||
=== | === ADC=== | ||
The user can access 7 ADC channels displayed on the terminals (see table). The maximum measured voltage is 5V. | |||
See. [[ADC/en]]. | |||
=== Terminal blocks=== | |||
See also [[Управление низковольтной нагрузкой/en| Low voltage load control]]. | |||
{| border="1" | {| border="1" | ||
| | | Terminal || function|| Max. V, I || GPIO || olinuxino output || default state* || comments | ||
|- | |- | ||
| | | Terminal strip 2 || [[low-voltage load Control|FET]]/[[ADC]] || 30V, 2A|| 32 || 3 @ CON1 || Open || open collector Output, [[ADC/en]] channel 3 | ||
|- | |- | ||
| | | Terminal strip 3 || [[Управление низковольтной нагрузкой/en|FET]]/[[ADC/en]] || 30V, 2A|| 33 || 4 @ CON1 || Closed || open collector output, [[ADC/en]] channel 0 | ||
|- | |- | ||
| | | Terminal strip 4 || [[low-voltage load Control/en|FET]]/[[ADC/en]] || 30V, 2A|| 34 || 5 @ CON1 || Closed || open collector Output, [[ADC/en]] channel 1 | ||
|- | |- | ||
| | | Terminal strip 5 || [[low-voltage load Control/en|FET]]/[[ADC/en]] || 30V, 2A|| 35 || 6 @ CON1 || Open || open collector Output, [[ADC/en]] channel 2 | ||
|- | |- | ||
| | | Terminal strip 6 || [[low-voltage load Control/en|FET]]/[[ADC/en]] || 30V, 2A|| 39 || 10 @ CON1 || Undefined || open collector Output, [[ADC/en]] channel 4 | ||
|- | |- | ||
| | | Terminal strip 7 || [[low-voltage load Control/en|FET]]/[[ADC/en]] || 30V, 2A|| 1 || 12 @ CON1 || Undefined || open collector Output, [[ADC/en]] channel 6 | ||
|- | |- | ||
| | | Terminal strip 8 || GND|| || || | ||
|- | |- | ||
| | | Terminal strip 9 || [[GPIO/en|GPIO operation]]/[[ADC/en]] || 3.3 V, 10mA|| 2 || 13 @ CON1 || 47K pull-up|| ADC channel 7 | ||
|- | |- | ||
| | | Terminal strip 10 || [[GPIO/en|GPIO operation]] || 3.3 V, 10mA|| 3 || 14 @ CON1 || 47K pull-up || | ||
|- | |- | ||
| | | Terminal strip 11 || [[GPIO/en|GPIO operation]] || 3.3 V, 10mA|| 4 || 15 @ CON1 || 47K pull-up || | ||
|- | |- | ||
| | | Terminal strip 12 || [[RS-485/en]] A|| || || UART1 from sc16is752 | | |if there is RS-485 | ||
|- | |- | ||
| | | Terminal strip 13 || [[RS-485/en]] B|| || || UART1 from sc16is752 | | |if there is RS-485 | ||
|- | |- | ||
| | | Terminal strip 14 || GND|| || || | ||
|- | |- | ||
| | | Terminal strip 15 || +3.3 v || 0.5 A || || | ||
|- | |- | ||
| | | Terminal strip 16 || +5.0 v || 0.5 A || || | ||
|- | |- | ||
| | | Terminal strip 17 || Vin|| 22 || || || ||Input voltage; ADC channel 5 | ||
|- | |- | ||
| | | Terminal strip 18 || GND|| || || | ||
|- | |- | ||
| | | Terminal strip 19 || [[low voltage load control/en|Power FET]] || 60V, 3A|||| 28 @ CON2 || Undefined || with hardware [[PWM/en|PWM]] | ||
|- | |- | ||
|} | |} | ||
/* | /* When the system boots, transistors will be in these States. This is a feature (bug) version of WB2.8. | ||
===GPIO=== | ===GPIO=== | ||
See [[Список GPIO/en| List of GPIOs]]. | |||
===Debug UART=== | ===Debug UART=== | ||
[[Image:UEXTPINS.jpg|thumb|UEXT pinout for [[Insulation-displacement connector|IDC]] connector<br/>(looking into connector on host board)]] | [[Image:UEXTPINS.jpg|thumb|UEXT pinout for [[Insulation-displacement connector|IDC]] connector<br/>(looking into connector on host board)]] | ||
Output to uext1 connector (black connector with ten pins on the long side of the Board). | |||
== | == Source files == | ||
See [[Wiren Board 2.8. Исходные файлы/en| Wiren Board v.2.8 source files]] | |||
=== | === Board drawing=== | ||
[[Файл:WB 2.8 chertej.pdf]] | [[Файл:WB 2.8 chertej.pdf]] |
правки